| Model # | Type | Special Features | Channels | W/@ 8 ohms | W/@ 4 ohms | W/Bridged @ 8 ohms | Color | Years Produced | Country | Specifications | 06/08/2008 |
| 4000 | Receiver | 2 | 0 | 0 | |||||||
| 4000t | Pre Amp | 2 | Silver | 86-89 | USA | Phono Inputs: Frequency Response, Within +0.25 dB of extended RIAA curve; Gain at 1 kHz (phono stage only), Phono 1 (moving magnet): 30 dB, Phono 2 (moving coil): 60 dB; IHF Input Sensitivity (re 0.5 V out), Phono 1: 1-6 mV, Phono 2: 0.05 mV; Input Impedance, Phono 1: 47 kW @ 0, 180, or 390 pF, Phono 2: 39 W; S/N Ratio, IHF A, Phono 1: 89 dB re 5 mV, Phono 2: 84 dB re 0.5 mV; Overload (Phono 1), 100 mV @ 1 kHz, 1 V at 20 kHz. High-Level Inputs: Frequency Response, 20 Hz to 20 kHz: +0, -0.25 dB, 1.5 Hz to 60 kHz: +0, -3 dB; Gain, 15/25 dB; IHF Input Sensitivity, 50 mV in for 0.5 V out; Input Impedance, 47 kW; Output Impedance, Main Outputs: 910 W, Tape and External Processor Outputs: 2 kW; S/N Ratio, IHF A, Hologram out: >100 dB, Hologram in: >100 dB; Distortion, THD, SMPTE 0.05% or less; IM, IHF IM typically 0.003%, T.I.M.: unmeasurable; Infrasonic Filter, -3 dB at 15 Hz, 12 dB/octave; Autocorrelator (patented), Noise reduction approximately 3 dB at 1.5 kHz, increasing to 12 dB from 3 kHz to 8 kHz, Low-frequency noise reduction -3 dB at 200 Hz, increasing to 9 dB from 100 Hz to 20 Hz; Surround Sound, Delay: 20 ms, Distortion: 0.25% or less, S/N Ratio, IHF A: 85 dB referenced to 5.3 Vrms out at 1 kHz; Dimensions, 19" x 6¾" x 8½"; Weight, 11 lbs. (5 kg) | |||||
| A-220 | Amplifier | 2 | 110 | 175 | 350 | Gold Plated RCA Jack Connections, Dual analog lighted meters with range selection switch, Meter light On/Off switch, Individual calibrated level trim controls for each channel, Removable handles for 17" cabinet space (with trim caps), Designed and built in Woodinville, Washington, USA, Frequency Response: 20-20kHz +0,-0.2dB, Power Output: FTC 20hz-20khz 8ohm 110 watts per channel, 4ohm 175 watts per channel, Bridged mono power output: 350 watts into 8 ohms, THD: less than 0.03%, Dynamic Headroom: >1.0dB @ 8ohms both channels driven, Gain: 29.0 dB (+/- 0.5dB), Input Impedance 50 kohms, Damping Factor: >150 typical (20hz-20 khz) | |||||
| A-400x | Amplifier | 2 | 200 | 300 | 600 | Black | 95 | SPECS: (Power output) 200watts per channel into 8ohms; 300watts per channel into 4ohms; Bridged mono operation - 600watts into 8ohms, all at 20Hz to 20kHz, nmt 0.2% THD --- (Dynamic Headroom) 2.0dB @ 8ohms; 2.5dB @ 4ohms --- (Freq Response) 20Hz to 20kHz (+0,-0.25dB) --- (Crosstalk) >70dB @ 1kHz --- (Damping Factor) >150 (@ 1kHz into 8ohms) --- (Input Impedence) 47kOhms --- (Sensitivity) 1.41V rms for rated power into 8ohms @ 1kHz (±0.5dB); 100mV for 1W into 8ohms (±0.5dB) --- (Gain) 29.0dB (±0.5dB) --- (Input-to-Output Phase) 0° (±10°) --- (IM Distortion) <0.03% --- (THD) <0.2% --- (Signal-to-Noise Ratio) >115dB (A-weighted, referenced to rated power); >91dBW (A-weighted, referenced to 1W) --- (Slew Rate) >10V/µS | |||
| A-500X | THX Certified | 2 | 250 | Black | |||||||
| A-753X | THX Certified | 3 | 250 | Black | |||||||
| A-760x | Theater Amp | THX Certified, 1150WPC @ 2 ohms | 2 | 380 | 600 | 1200 | Black | Frequency Repsonse: 20-20kHz +0,-0.2dB Power Output: FTC 20hz-20khz 8ohm 380 watts per channel, 4ohm 600 watts per channel, 2ohm 1150 watts per channel, Bridged mono power output: 1200 watts into 8 ohms, THD: less than 0.08%, Dynamic Headroom: >1.0dB @ 8ohms both channels driven, Gain: 29.0 dB (+/- 0.5dB), Input Impedance 47 kohms, Damping Factor: >150 typical (20hz-20 khz), | |||
| AL-III | Speaker | 48" ribbon, 1X10" down firing woofer, 3 pots, 4 ohm | 1 | Oak or Satin Black | 92 | USA | Frequency Response: 24 Hz to 20 kHz (includes typical room gain. Anechoic response is 34 Hz to 20 kHz). Impedance: Nominal 4 ohms. Sensitivity: 86 dB. Crossover: Ribbon operates from 150 Hz to 20 kHz; woofer reproduces all frequencies below 150 Hz. Ribbon Driver: 48-inch dipole ribbon. Woofer: 10-inch Quasi-Butterworth 3rd-order aligned woofer system, which fires downward in a circular pattern. Recommended Power: Up to 575 watts per channel; 65 watts minimum, 8 ohm rated. Front Wings: Solid oak. Woofer Box: Hexagonal, with durable black coating. The box is vented. Shipping Weight: 80 lbs. each. Dimensions: 14.5" (37 cm) W x 16.5" (42 cm) D x 72.5" (185 cm) H. | ||||
| AL-III Plus | Speaker | 48" ribbon, 1X10" down firing woofer, no pots, 4 ohm | 1 | 0 | 0 | Oak or Satin Black | USA | Anechoic Frequency Response: 34 Hz to 20 kHz, ±3 dB. Impedance: Nominal 4 ohms. Sensitivity: 86 dB ref. to 1 watt at 1 meter. Crossover: 150 Hz. Ribbon Driver: 48-inch dipole ribbon. Woofer: 10-inch Quasi-Butterworth 3rd-order aligned woofer system, which fires downward in a circular pattern. Recommended Power: Up to 500 watts per channel; 65 watts minimum, 8 ohm rated. Front Wings: Solid oak. Woofer Box: Hexagonal, with durable black coating. The box is vented. Net Weight: 80 lbs. each. Shipping Weight: 96 lbs. each. Dimensions: 14.5" (37 cm) W x 16.5" (42 cm) D x 72.5" (185 cm) H | |||
| AV-140 | Amplifier | 2 | 210 | Black | 210WPC @ 8 ohms mono or 2 channel mode. It can power up to 4 speakers and can run 4, 6 or 8 ohm speakers. THD is <.03%, signal-to-noise ratio is >112 dB rated at 20Hz-20kHz | ||||||
| AV-220 | Amplifier | 2 | Black | ||||||||
| AV-405 | Theater Amp | 410W @ 8 ohms total, 5 channel | 5 | 80 | Black | 93 | |||||
| AV-504X | Theater Amp | THX Certified | 5 | Black | |||||||
| AV-505 | Theater Amp | Power Steering, 130W to any channel @ 8 ohms, 5 channel, 400W total | 5 | 80 x 5, 120 x 2 | Black | Each channel protected by: individual fusing, excess temperature sense, DC fault sense, power-on delay, shorted load sense. Minimal signal path design, with on card I/O connectors eliminating internal interconnect cables, Gold Plated RCA Jack Connections, Individual calibrated level trim controls for each channel, Removable handles for 17" cabinet space (with trim caps), Designed and built by Carver Corporation in Lynnwood, WA USA, Frequency Repsonse: 20-20kHz +0,-0.2dB, Power Output: FTC 20hz-20khz, 8ohm 120 watts per channel two channels driven, 8ohm 80 watts per channel all channels driven, THD: less than 0.08%, Dynamic Headroom: >1.1dB @ 8ohms all channels driven, Gain: 29.0 dB (+/- 0.5dB), Input Impedance 50 kohms, Damping Factor: >300 typical (20hz-20 khz) | |||||
| AV-505x | Theater Amp | THX Certified, Power Steering, 130W to any channel @ 8 ohms, 5 channel, 400W total | 5 | 80 x 5, 120 x 2 | Black | Gold Plated RCA Jack Connections, Individual calibrated level trim controls for each channel, Removable handles for 17" cabinet space (with trim caps), Designed and built by Carver Corporation in Lynnwood, WA USA, Frequency Repsonse: 20-20kHz +0,-0.2dB, Power Output: FTC 20hz-20khz, 8ohm 120 watts per channel two channels driven, 8ohm 80 watts per channel all channels driven, THD: less than 0.08%, Dynamic Headroom: >1.1dB @ 8ohms all channels driven, Gain: 29.0 dB (+/- 0.5dB), Input Impedance 50 kohms, Damping Factor: >300 typical (20hz-20 khz THX Certified | |||||
| AV-63 | Theater Amp | 3 | 65 | 90 | 180 | Black | 91-92 | 65 watts, 3 channels driven into 8 ohms, 20-20kHz with no more than 0.5% · 90 watts x 3 into 4 ohms, 20-20kHz with no more than 0.5% THD · 3-ch. Operation: 180 watts ch. 1/2 bridged, 60 watts x 2 ch. 3 &4 output | |||
| AV-634 | Theater Amp | 3/4 | 60 | Black | 92-93 | ||||||
| AV-64 | Theater Amp | 60 watts X 4 into 8 ohms, 100 watts x 4 into 4 ohms, 3-ch. Operation: 180 watts/channel 1/2 bridged, 60 watts x 2 ch. 3&4 output | 4 | 60 | 100 | 180 | Black | 89-92 | Built-in 2-way 18dB/octave electronic crossover w/75Hz turnover point · 60 watts, 4 channels driven into 8 ohms, 20-20kHz with no more than 0.5 % THD · 100 watts x 4 into 4 ohms, 20-20kHz with no more than 0.5% THD · 3-ch. Operation: 180 watts/channel 1/2 bridged, 60 watts x 2 ch. 3&4 output · Rear panel trim/balance controls | ||
| AV-705x | Theater Amp | THX Certified, up to 200W to any 1 channel | 5 | 125 | Black | ||||||
| AV-753x | Theater Amp | THX Certified | 3 | 250 | Black | ||||||
| AV-806x | Theater Amp | THX Certified | 6 | 133 | 1 X 360 + 4 X 133 | Black | 93 | ||||
| AVR-100 | Receiver | EUR64162 Remote | 2 | 150 | Anthracite | 87-90 | |||||
| AVR-180 | Receiver | 2 | 180 | Anthracite | |||||||
| C-1 | Pre Amp | MM, MC, SH | 2 | Anthracite | 81-89 | USA | |||||
| C-11 | Pre Amp | MM, MC, SH | 2 | Black | 89-91 | USA | |||||
| C-15v | Pro Pre Amp | Dolby Pro-Logic, Vocal Zoom, S-Video, AV, Dual Zone, RH-15V Remote | 5 | 93 | |||||||
| C-16 | Pre Amp | MM, MC, SH, Spectral Tilt | 2 | 89-93 | USA | ||||||
| C-19 | Pre Amp | Tubes, MM, MC, SH, Spectral Tilt | 2 | 89-93 | USA | ||||||
| C-1000a | Pre Amp | Silver | USA | ||||||||
| C-2 | Pre Amp | MM, MC | 2 | Anthracite | USA | ||||||
| C-20v | Pre Amp | AV, RH-20 Remote, Dolby Pro-Logic, Delay, S-Video In/Out | 5 | 93 | |||||||
| C-3 | Pre Amp | 2 | Black | 92-96 | Just 1-3/4 inches tall, the C-3 is ideal for custom installations. Despite its minimal size, truly a state-of-the-art preamplifier with exceptional detail and openess * 8 audio inputs * Sonic Hologram Generator for true 3-dimensional sound * Dual tape monitors w/dubbing * Bass/treble & loudness equalization * Balance control * CD Direct input for the most accurate CD performance * 2 AC convenience outlets * Stereo headphone jack * External processor loop * Tone defeat | ||||||
| C-4000 | Pre Amp | 2 | Silver | 80-85 | USA | Phono Inputs: Frequency Response, Within ±1 dB of RIAA curve from 20 Hz to 20 kHz; Gain (early, identical MM phono stages only), 30 dB; Gain (later, with both MM and MC phono stages) Phono 1 (moving magnet): 35 dB, Phono 2 (moving coil): 60 dB; IHF Input Sensitivity (re 0.5 V out), Phono 1: 1-6 mV, Phono 2: 0.05 mV; Input Impedance, Phono 1: 47 kW @ 0, 180, or 390 pF, Phono 2: 39 W; S/N Ratio (later, with both MM and MC phono stages), IHF A, Phono 1: 81 dB re 5 mV, Phono 2: 75 dB re 0.5 mV; Overload (Phono 1), 100 mV @ 1 kHz, (Phono 2), 5 mV @ 1 kHz. High-Level Inputs: Frequency Response, 20 Hz to 20 kHz: ±1 dB; IHF Input Sensitivity, 250 mV in for 2.5 V out; Input Impedance, 47 kW; Output Impedance, Main Outputs: 910 W, Tape and External Processor Outputs: 2 kW; S/N Ratio, IHF A, Hologram out: >100 dB, Hologram in: >100 dB; Distortion, THD, SMPTE 0.05% or less; IM, IHF IM typically 0.003%, T.I.M.: unmeasurable; Infrasonic Filter, -3 dB at 15 Hz, 12 dB/octave; Autocorrelator (patented), Noise reduction approximately 3 dB at 1.5 kHz, increasing to 12 dB from 3 kHz to 8 kHz, Low-frequency noise reduction -3 dB at 200 Hz, increasing to 9 dB from 100 Hz to 20 Hz; Dimensions, 19" x 6¾" x 8½"; Weight, 11 lbs. (5 kg) | |||||
| C-5 | Pre Amp | RH-5 Remote, Dual Zone, SH | 2 | Black | 90-93 | ||||||
| C-500 | Amplifier | 2 | 250 | 454 | Silver, later units Anthracite | 80-83 | USA | ||||
| C-6 | Pre Amp | 2 | 89-90 | ||||||||
| C-9 | Processor | 2 | Black | 81-89 | USA | Injection Ratio: Normal or Theoretical; Listening Aperture: Narrow or Wide; | |||||
| CA-120 | Pro Amp | ||||||||||
| CA-400 | Pro Amp | Pro Amplifier | 2 | 200 | |||||||
| CA-900 | Pro Amp | 0 | 0 | 0 | |||||||
| CBA-1000 | |||||||||||
| Cinema System 5.1 | Speaker | 6 speaker, 150W, subwoofer | |||||||||
| Cinema System 5.2 | Speaker | 5 speaker, 300W, subwoofers | |||||||||
| CM-1040 | Integrated Amp | 2 | 40 | 40 | Black | 90 | China | ||||
| CM-1065 | Integrated Amp | 2 | 65 | 65 | Black | 90 | China | 65 Watts per Channel in 8 ohms, 20-20,000Hz +/-1dB, 0.05% THD, 65 Watts per Channel in 4 ohms, 20-20,000Hz, Two Illuminated Power Meters, Five Source Inputs plus Monitor Input/Output for recording to Tape, Music Server, etc., Sonic Holography Carver exclusive Treble and Bass Tone Controls with Loudness (or CD Direct if you prefer) Two Pairs of Speaker Output with Screw-Down Terminals that accept Blade, Pin or Banana Plug Gold-plated Interconnect Jacks are used on the Phono, CD and Preamp Out/In | |||
| CM-1090 | Integrated Amp | RH-5 Remote | 2 | 90 | 90 | Black | 90 | Japan | |||
| CM-2002 | Integrated Amp | 2 | 105 | 150 | Black | 90 | China | Frequency Response: 20Hz -20kHz, 105 watts per channel 8ohm, 150 watts per channel 4ohm, Separation: >70db @ 1 kHz, THD: less than 0.08% at full power | |||
| CMV-1185 | Theater Amp | RH-85 Remote | Black | 93 | China | ||||||
| CT-15v | Pre Amp/Tuner | 5 | |||||||||
| CT-17 | Pre Amp/Tuner | RH-17/RH-5/RC-CT17 Remote, 5 channel, AV, SH, dual zone, Dolby Pro-Logic | 2 | Black | 89-93 | Japan | |||||
| CT-17/M-0.5t | Pre Amp | 2 | Black | 89-90 | Japan | ||||||
| CT-23 | Pre Amp/Tuner | RH-23 Remote, 5 channel, AV, Advanced SH, dual zone | 2 | Black | 95 | Japan | |||||
| CT-24 | Pre Amp/Tuner | 2 | Black | ||||||||
| CT-25 | Pre Amp/Tuner | 2 | Black | ||||||||
| CT-25.1 | Pre Amp/Tuner | RH-88B Remote | 2 | Black | USA | ||||||
| CT-26v | Pre Amp/Tuner | RH-88B Remote | 5 | Black | |||||||
| CT-27v | Pre Amp/Tuner | 5 channel, AV, Dolby Pro-Logic, RH-27V Remote | 5 | Black | 93 | ||||||
| CT-28v | Pre Amp/Tuner | RH-28V Remote, S-video inputs and outputs | 5 | Black | Japan | 5.1 Dolby Pro Logic decoding and output 6 Digital Signal Processing program modes Subwoofer output with crossover 4 audio inputs INCLUDING PHONO 3 A/V inputs composite video input and output S-Video input and output 5 .1 channel output with subwoofer level 30 tuner station presets | |||||
| CT-29v | Pre Amp/Tuner | RH-29V Remote, 5 channel, AV, SH, dual zone, Dolby Pro-Logic, S-video inputs and outputs, mullti-room remote capable | 5 | Black | 93 | Advanced Dolby Pro Logic Surround w/adjustable delay and auto input balance. - Matrix surround modes with DSP and adj. delay from 0-90ms. - DSP memory - Seven audio inputs, 3 composite video inputs, and three S Video inputs. - Five outputs for Surround. - 18db/octave variable sub output. - Three composite vid out, and three S vid outputs + video monitor out. - Multi room selector for playing different soruces in different rooms. - Digital AM/FM tuner - EQ in and out connections - Vocal zoom control - Programmable remote - Motor driven master control (from remote). Very cool. | |||||
| CT-3 | Pre Amp/Tuner | Remote RH-74A | 2 | Black | 92 | ||||||
| CT-30x | Pre Amp/Tuner | Black | |||||||||
| CT-5.1 | Dolby® Digital Tuner/Preamp | 5 | Black | ||||||||
| CT-6 | Pre Amp/Tuner | RH-5 Remote, ACCD, SH, AV | 2 | 90 | Japan | ||||||
| CT-Seven | Pre Amp/Tuner | Remote CT-Seven/HTR001-0190, ACCD | 2 | Anthracite | 89-93 | 6 audio inputs· 27-button wireless infrared remote w/Carver CD player compatibility · Asymmetrical Charge-Coupled FM Detection circuitry · 16 AM/FM presets w/presets scan, stereo/mono, auto/manual controls · 3-band tone controls · Dual tape monitors w/dubbing · Mono button · Loudness equalization circuitry · Headphone monitor jack | |||||
| DPL-20 | Processor | RH-33 Remote | 93 | USA | |||||||
| DPL-33 | Processor | RH-23 Remote, Centre 25W @ 8 ohms, surround 15WPC @ 8 ohms X 2 | 3 | 15 | 90-93 | USA | |||||
| DTD-1880 | Digital Tape Deck | 93 | |||||||||
| DTL | Processor | Anthracite | 88-90 | USA | Input: 0 - 2 V; Input Impedance: 50 kW; Output: 2 V; Distortion: 0.005%; Frequency Response: 20 Hz - 20 kHz; Dither Signal: 0 dB, -70 dB; Dimensions: 173/8" W, 4: D, 1½ H. | ||||||
| DTL-100 | CD Player | Anthracite | 85-86 | Japan | |||||||
| DTL-200 | CD Player | RM-200 Remote | Anthracite | 86-87 | Japan | ||||||
| DTL-200 II | CD Player | RM-200 Remote | Anthracite | 87-89 | Japan | Frequency Response 5Hz to 20KHz +/- 0.2 dB, Distortion 0.007%, S/N 100 dB, Stereo Separation 90 dB, Dynamic Range 100 dB | |||||
| DTL-50 | CD Player | RM-50 | Anthracite | 86-89 | Japan | ||||||
| ECS-U | Misc. | 89-93 | USA | ||||||||
| GA-250 | Pro Guitar Amp | USA | |||||||||
| H-9AV | Processor | 89-93 | USA | ||||||||
| HR-722 | Receiver | RH-5/RC-HR752 Remote | 2 | 60 | 90 | Black | 89-91 | Japan | |||
| HR-732 | Receiver | RH-74A Remote | 2 | 60 | Black | 91-93 | Korea | 60 watts/channel RMS into 8 ohms 20-20kHz, both channels driven with no more than 0.09% THD ~ 6 audio inputs ~ 3 video inputs ~ 1 video output ~` Sonic Hologram Generator ~ Asymmetrical Charge-Coupled FM Detection Circuitry ~ 30 AM/FM presets ~` Preset scan and auto/manual tuning ~` Motorized volume control | |||
| HR-742 | Receiver | RH-74A Remote | 2 | Black | 91 | Korea | |||||
| HR-752 | Receiver | RH-5/RC-HR752 Remote, pre-in/main out, B speaker ambiance control | 2 | 100 | 150 | Black | 89-91 | Japan | |||
| HR-772 | Receiver | RH-77 Remote | 2 | 140 | Black | 90-93 | Korea | Transfer Function Modified ~ 140 watts RMS/channel into 8 ohms 20-20kHz, both channels driven with no more than 0.1% THD ~ A/B speaker selection ~ 20 random AM/FM station presets ~ Asymmetrical Charge-Coupled FM Detection circuitry ~ FM mono ~ Auto-scan/manual tuning ~ Signal strength indicator ~ Sonic Hologram Generator ~ 3 audio inputs ~ 2 video output ~ 1 video output ~ Dual tape monitors w/dubbing ~ Source Direct " strightwire" feature ~ 5-band rotary tone controls ~ Loudness equalization ~ Balance control ~ Motorized volume control ~ Pre-out sockets ~ Alpha-numeric source display ~ 2 convenience outlets ~ Headphone jack ~ 27-button remote control | |||
| HR-875 | Receiver | RH-87 Remote | 5 | Black | 93 | Japan | |||||
| HR-895 | Receiver | RH-89a is the credit card remote and the RH-90 is the full function remote | 5 | 110 X 2 + 75 centre + 30 X 2 surround | Black | 92 | Japan | ||||
| HTR-880 | RH-88B Remote | 5 | 85 | Black | Gold Plated RCA Jack Connections, Remote Control, Exclusive Power Steering circuitry provides over 50% more power on demand for selected amplifier channels, Phono Input Stage, Two AC outlets one switched and one unswitched, Removable handles for 17" cabinet space (with trim caps), Motor-driven Volume control can be operated from the remote control, Designed by Carver Corporation in Lynnwood, WA USA, Frequency Repsonse 20-20kHz +/- 0.5dB, S/N MM Phono A-Weighted > 75dB, Input Sensitivity for 0.5V 34mV, Input Impedance 47 kohms, Maximum Input Level 5.5V, Output Impedance 1 kohm, Maximum Output Level 7V Input, Sensitivity for 0.5V phono 3.5mV | ||||||
| HTR-885.1 | RH-88B Remote | 5 | 80 x 3, 30 x 2 | Black | 80 watts x 3 front channels, 30 watts x 2 rear channels, Discrete high-current amplifier design on all 5 channels, Phono Input stage, 5-way binding post outputs on all channels, Surround Field Expansion (S.F.X.) for a wider surround soundstage, 3 audio inputs, 2 audio/video inputs, 1 composite video output, 5.1 channel input allows the connection of a Dolby® Digital or DTS decoder, Subwoofer output allows the connection of a powered subwoofer, Digital Frequency Synthesis AM/FM Tuner, Random Presetting of up to 16 AM/FM stations, Gold-Plated RCA input jacks, Bass and Treble tone controls and balance control, Motor-Driven master volume control can be operated from the remote, Infrared remote control, Removable Handles for placement in 17" wide cabinet | ||||||
| IR-R1 | Remote System Link | 89 | |||||||||
| IR-R2 | Remote System Link | ||||||||||
| IR-T1 | Remote System Link | 89 | |||||||||
| IR-T4 | Remote System Link | ||||||||||
| IR-Z | |||||||||||
| KMOS-2150 | Car Amp | 100 | 200 at 4 ohms | 92-94 | Operating Voltage: 10.6 to 16VDC, Power Output: Stero Mode ( 20Hz-20kHz, both channels driven 14.4 VDC input): 4 ohms- 100watts for THD of .5%, 2 ohms-170 watts for THD of .5%, power Output: Mono Mode ( 20Hz-20kHz, 14.4VDC input: 4 ohms-200 watts for THD of.5%, Frequency Response ( for 1 watts into 4 ohms load): 20Hz-20kHz + 1 dB, Crossover: 18dB/Octave ( three pole ) Butterworth filter, 80Hz, Bass Boost: + 9db at 45Hz, Dimensions 3.5"H x 9.37"W x 7.5"D, Net Weight 10lbs | ||||||
| KMOS-2200 | Car Amp | 100 | 340 at 4 ohms | 92-94 | Operating Voltage: 10.6 to 16VDC, Power Output: Stero Mode ( 20Hz-20kHz, both channels driven 14.4 VDC input ) : 4 ohms - 100 watts for THD of .5%, 2 ohms- 170 watts for THD of .5% , Power Output: Mono Mode ( 20Hz-20kHz , 14.4VDC input): 4 ohms- 340 watts for THD of .5%, Frequency Response ( for 1 watts into 4 ohms load ): 20Hz-20kHZ + 1dB, Crossover: 18dB/octave ( three pole) Butterworth filter, 80Hz, Bass Boost: + 9dB at 45Hz, Dimensions 3.5"H x 11.37"W x 7.5"D, Net Weight 10lbs | ||||||
| KMOS-4200 | Car Amp | 50 | 150 at 4 ohms | 92-94 | Operating Voltage: 10.6 to 16VDC, Power Output: Stero Mode (20Hz-20kHz, four channels drven, 14VDC input) : 4 ohms- 50 watts for THD of 5%, 2 ohms - 75 watts for THD of .5%, Power Output: Mono mode ( 20Hz-20kHz, 14.4VDC input ) 4 ohms-150 watts for THD .5%, Frequency Response ( for 1 watt into 4 ohm load ) : 20Hz-20kHz + 1dB/Octave ( three pole ) Butterworth filter, 85Hz, Bass Boost: + 10dB at 40Hz, Minimum Load Impedance: 2 ohms recommended ( 4 ohms recommended for bridged operation ) Dimensions 3.5"H x 14.87"W x 7.5"D, Net Weight 13lbs | ||||||
| Lightstar Dir. | Pre Amp | 2 | Black | 93 | USA | ||||||
| Lightstar II | Amplifier | 2 | Black | 93 | USA | ||||||
| Lightstar Ref. | Amplifier | True dual mono inside single chassis design. Weight 76lbs Cost new $5,000.00 Runs very hot. (I think the reference is more class A biased) | 2 | 300 | 600 | 1200 | Black | 93 | USA | Solid-state stereo power amplifier. Power output: 300W into 8 ohms (24.8dBW), 600W into 4 ohms (24.8dBW), 1200W into 2 ohms (24 8dBW}. frequency response: 20Hz-20kHz +/-O.5dB. Full power bandwidth: 10Hz-20kHz. Chanel separtion: > 60dB at 1kHz. Damping factor >200, equivalent to an output impeince of less than 0.04 ohms. THD: <0> 50V/us. Output impedance: <0.04 ohms. Input sensitiviy: low gain, 1.74V RMS; high gain, 430mV RMS. Input impedance: 50k ohms. Power consumption per side: 60W at idle, 250W with musical program, 1440W nominal continuous. Dimensions: 19" W by 6.9" H by 17.8" D with handles. Weight 72 lbs (net). Warranty: 5 years, parts and labor. Price: $3995. Approximate number of dealers: 25. Manufacturer Carver Corporation, 20121 48th Aw. W., Lynnwood, WA 913036 | |
| LS-2 | 2 channel design with single power supply. Weight 40 lbs Cost new $2,500.00 Runs cool (using tracking down design). More like a Sunfire amp. | 2 | 300 | 600 | 1200 | Black | USA | Specifications: 300 Watts RMS - 8ohms, 600 Watts RMS - 4ohms, 1200 Watts RMS - 2ohms, 2400 Watts available for >2000ms, Frequency Response : 20 Hz to 20k Hz(+- 0.5dB), Full Power Bandwidth : 5 Hz to >20k Hz, CrossTalk >70 dB@1k, Damping factor >200, Output Impedence < 0.4 ohms, Input to Output Phase angle < 6.5 degrees, CCMR : < 50dB@1k, THD : <0.2%, Signal to Noise low gain: 114dB, high gain : 103 dB, A-Weighted, refenced to rated power, Power Consumption, 50W at idle, 250W with musical program, 1440W nominal continuous, Power Requirements 120VAC, Display: Dual Analogue Meters(lighted), 0dB=300 watts into 8ohms, Weight 42lbs | |||
| LS-Preamp | Pre Amp | 2 | Black | USA | |||||||
| M-0.5t | Amplifier | 2 | 140 | 220 | No | Silver | 88-90 | USA | |||
| M-1.0t | Amplifier | Long term, sustained RMS power, 500 watts into 4 ohms, 350 watts into 8 ohms. | 200 | 400 | 1000 | Silver | 86-90 | USA | Power Output: 200 watts/channel into 8 ohms 20 Hz to 20 kHz, both channels driven, with no more than 0.15 percent THD, 400 watts/channel into 8 ohms 20 Hz to 20 kHz, both channels driven, with no more than 0.15 percent THD. Long term, sustained RMS power, 500 watts into 4 ohms, 350 watts into 8 ohms. Bridged Mono RMS power, 1000 watts into 8 ohms. Noise: -110 dB, IHF A-weighted. Frequency Response, +0, -3 dB, 10 Hz - 100 kHz. Slew Factor, greater than 200. Weight: 20 lbs. Transfer function modified to emulate a Conrad Johnson Premier Five. LED power meters | ||
| M-1.5 | Amplifier | 2 | 350 | 600 | No | Silver | 82-88 | USA | Power Output: 350 watts per channel RMS into 8 ohms, both channels driven, with no more than 0.5 percent total harmonic distortion, 20 to 20,000 Hz. 600 watts per channel into 8 ohms for musically significant time periods. 750 watts per channel of Dynamic Headroom. Noise: 100 dB, IHF "A" weighting. IM distortion: Less than 0.5%. Input Impedance: 100 kohms. Load Impedance: Recommended for driving impedances from 2 to 32 ohms. Power consumption: 32 watts idle, 1500 watts full power. Display ballistics: 1 millisecond attack, 1 second release. Dimensions: 3½" H, 19" W, 10½" D. Wight: 16 lbs. Initially released prior to the famous/infamous challenges that brought on the "t-mods." LED power meters | ||
| M-1.5t | Amplifier | 2 | 350 | 600 | No | Silver | 82-88 | USA | Power Output: 350 watts per channel RMS into 8 ohms, both channels driven, with no more than 0.5 percent total harmonic distortion, 20 to 20,000 Hz. 600 watts per channel into 8 ohms for musically significant time periods. 750 watts per channel of Dynamic Headroom. Noise: 100 dB, IHF "A" weighting. IM distortion: Less than 0.5%. Input Impedance: 100 kohms. Load Impedance: Recommended for driving impedances from 2 to 32 ohms. Power consumption: 32 watts idle, 1500 watts full power. Display ballistics: 1 millisecond attack, 1 second release. Dimensions: 3½" H, 19" W, 10½" D. Wight: 16 lbs. Transfer function modified to emulate a Mark Levinson ML-2. LED power meters | ||
| M-200t | Amplifier | 2 | 120 | 200 | 350 | Anthracite | 82-88 | USA | Emulated the transfer function of no particular tube amp | ||
| M-2020 | Car Amp | 20watts x2 at 4 ohms | |||||||||
| M-2030 | Car Amp | 30watts x2 at 4 ohms | |||||||||
| M-2040 | Car Amp | 40watts x2 at 4 ohms | |||||||||
| M-2050i | Car Amp | 50watts x2 at 4 ohms | |||||||||
| M-2060 | Car Amp | 60watts x2 at 4 ohms | |||||||||
| M-2080 | Car Amp | 80watts x2 at 4 ohms | |||||||||
| M-2090i | Car Amp | 90watts x2 at 4 ohms | |||||||||
| M-2120 | Car Amp | 120watts x2 at 4 ohms | |||||||||
| M-2200 | Car Amp | 200watts x2 at 4 ohms | |||||||||
| M-240 | Car Amp | 40watts x2 at 4 ohms | |||||||||
| M-30 Satellites | Speaker | 92-93 | |||||||||
| M-4.0t | Amplifier | Front mounted power switch | 2 | 375 | 500 | 1000 | Anthracite | 89-90 | USA | Power Output: 375 watts per channel RMS into 8 ohms, 500 watts per channel RMS into 4 ohms, 1000 watts bridged mono. LED power meters | |
| M-400 | Amplifier | 2 | 201 | 250 | 500 | Champagne | 80-83 | USA | LED power meters, Impedance switch | ||
| M-400a | Amplifier | 2 | 201 | 250 | 500 | Silver | 80-83 | USA | LED power meters | ||
| M-400t | Amplifier | Power steering | 2 | 201 | 250 | 500 | Anthracite | 85-89 | USA | 265 WPC at 2 ohms 400 watts bridged at 4 ohms LED power meters | |
| M-4050 | Car Amp | White | 50watts x4 at 4 ohms | ||||||||
| M-4060 | Car Amp | White | 60watts x4 at 4 ohms, 4X40WRMS@ 8OHM / 2X120WRMS A PONTE @ 8 OHM | ||||||||
| M-4120 | Car Amp | White | 120watts x4 at 4 ohms | ||||||||
| M-500 | Amplifier | Huge power meters, no power switch | 2 | 251 | 450 | 700 | Anthracite | 81-85 | USA | ||
| M-500t | Amplifier | Huge power meters, T-modded, front mounted power switch | 2 | 251 | 450 | 700 | Anthracite | 85-89 | USA + Japan | Emulated the transfer function of no particular tube amp | |
| MCt | Moving Voice Coil Transformer | 89-93 | Available load impedances: 3.9, 39, and 110 W. | ||||||||
| MD/A-420 | CD Player | RH-42 Remote | Black | 91-92 | |||||||
| MD/V-500 | CD Player | RH-5 Remote | Black | 91-93 | |||||||
| MULTI-ROOM KIT | Remote System Link | ||||||||||
| MV-5 | CD Player | RH-05 Remote | 2 | Black | China | ||||||
| MXR-130 | Receiver | 130WPC @ 8 ohms | 2 | 130 | No | Anthracite | 86-88 | Japan | |||
| MXR-150 | Receiver | 150WPC @ 8 ohms, Wood sides and rack handles | 2 | 150 | No | Anthracite | 87-88 | Japan | |||
| MXR-180 | Receiver | CRC-180 Remote | 2 | 180 | Anthracite | ||||||
| MXR-2000 | Receiver | 2 | 200 | Anthracite | 85-88 | ||||||
| MXR-6200 | Receiver | 2 | 100 | Anthracite | 89-90 | Japan | |||||
| MXR-6250 | Receiver | Anthracite | 89-90 | ||||||||
| MXR-90 | Receiver | Anthracite | 87-88 | ||||||||
| MXR-900 | Receiver | Anthracite | 85-88 | ||||||||
| One Tube | Pre Amp | 91-92 | |||||||||
| PG-2 | Paging Module | ||||||||||
| PM-1.5 | Pro Amp | 2U | 2 | 450 | 600 | 1200 | Silver | USA | |||
| PM-100 | Pro Amp | ||||||||||
| PM-120 | Pro Amp | ||||||||||
| PM-1200 | Pro Amp | 2 | 450 | 600 | Black | USA | |||||
| PM-1201 | Pro Amp | 300WPC at 16 ohms, 1000W 16 ohm bridged, 2U | 2 | 450 | 600 | 1200 | Black | USA | |||
| PM-125 | Pro Amp | 1U | Black | USA | |||||||
| PM-1250 | Pro Amp | 10 lbs | 2 | 465 | 625 | USA | |||||
| PM-1400 | Pro Amp | ||||||||||
| PM-175 | Pro Amp | ||||||||||
| PM-2.0 | Pro Amp | ||||||||||
| PM-200 | Pro Amp | 2U | 2 | 100 | Black | USA | |||||
| PM-300 | Pro Amp | ||||||||||
| PM-350 | Pro Amp | 3U? | 2 | 350 | 450 | 900 | Black | USA | |||
| PM-420 | Pro Amp | 2U | 2 | 135 | 210 | 420 | Black | ||||
| PM-600 | Pro Amp | 625W at 70V, 2U | 2 | 200 | 300 | 700 | Black | USA | |||
| PM-700 | Pro Amp | 2U | 2 | 225 | 350 | 700 | Black | USA | |||
| PM-900 | Pro Amp | 2 | 350 | 450 | 900 | Anthracite | USA | ||||
| PM-950 | Pro Amp | ||||||||||
| PMA-2022 | Car Amp | ||||||||||
| PMA-2062 | Car Amp | ||||||||||
| PMA2150 | Car Amp | ||||||||||
| PMA-4075 | Car Amp | ||||||||||
| PM-CX4 | |||||||||||
| PMT-2 | |||||||||||
| PMX | X-Over | ||||||||||
| PRH-2 | |||||||||||
| PSB-11 | |||||||||||
| PSC-50 | Pro Pre Amp | RH-5 Remote, pro version of the C-5 | 2 | 90-93 | Japan | ||||||
| PSC-60 | Pro Pre Amp | Pro version of the C-6 | 2 | 89-90 | |||||||
| PSB-36b | Pro CD Changer | Pro rack mount version of TLM-3600, no handles, made by Yamaha, uses Yamaha 10CD cartridges, RH-36 remote | Japan | ||||||||
| PST-12 | Pro Tape Deck | Japan | |||||||||
| PST-14 | Pro Tape Deck | RH-14 Remote | |||||||||
| PST-24 | Pro Tape Deck | RH-24 Remote | |||||||||
| PT-1250 | Pro Amp | ||||||||||
| PT-1800 | Pro Amp | 2 | Silver | USA | |||||||
| PT-2400 | Pro Amp | 2 | USA | ||||||||
| R-6200 | HTR-0001-0090 Remote | ||||||||||
| R-6250 | HTR-0001-0080 Remote | ||||||||||
| RAC-6 | Remote System Link | 89 | |||||||||
| RAC-6A | |||||||||||
| RH-FC | |||||||||||
| RSL | Remote System Link | 89 | |||||||||
| SBC-8503 | |||||||||||
| SD/A-350 | CD Player | WW41223D8 Remote | Black | 91-93 | |||||||
| SD/A-360 | CD Player | Remote RH-60 | Black | 93 | |||||||
| SD/A-370 | CD Player | RH-36 Remote | Black | 92 | |||||||
| SD/A-390t | CD Player | Tube CD Changer, RH-39 Remote | Black | 93 | |||||||
| SD/A-410 | CD Player | RH-41 Remote | Black | 92-93 | |||||||
| SD/A-450 | CD Player | RH-45 Remote | Black | 91-93 | |||||||
| SD/A-490t | CD Player | Tube single CD Player, RH-49 Remote | Black | 91 | |||||||
| Silver One | Tube Pre Amp | 92 | |||||||||
| Silver-6 | Amplifier | 1 | 300 | Piano Black | 91-93 | 300WPC monobloc reference tube amp | |||||
| Silver-7 Lab. | Amplifier | Tube amp, 510WPC@1 ohm | 1 | 375 | 475 | Piano Black | 88-93 | 8 ohm FTC rated power/ch. 575w 4 ohm FTC rated power/ch 900w 2 ohm dynamic power/ch 1180w 4/8 ohm FTC rated THD .5% Rated full power bandwidth 20-20kHz S/N IHF A-Weighted db >100 Slew rate 300 | |||
| Silver-7 MKII | Amplifier | Tube amp, 510WPC@1 ohm | 1 | 375 | 475 | Piano Black | 93 | ||||
| Silver-7t | Amplifier | 1000W @ 2 ohms | 1 | 575 | 900 | Piano Black | 91-92 | Vacuum Tube Transfer Function Modified·575 watts into 8 ohms,20kHz with no more than 0.5% THDS·900 watts into 4 ohms,20-20kHz with no more than 0.5% THD·1000 into 2 ohms,20-20kHz with no more than 0.5%· Lit analog power meter | |||
| Silver-7t MKII | Amplifier | 1000W @ 2 ohms | 1 | 550 | 900 | Piano Black | 89-91 | Vacuum Tube Transfer Function Modified·550 watts into 8 ohms,20kHz with no more than 0.5% THDS·900 watts into 4 ohms,20-20kHz with no more than 0.5% THD·1000 into 2 ohms,20-20kHz with no more than 0.5%· Lit analog power meter | |||
| Silver-9t | Amplifier | 1000W @ 2 ohms | 1 | 550 | 900 | Piano Black | 91-93 | Vacuum Tube Transfer Function Modified·550 watts into 8 ohms,20kHz with no more than 0.5% THDS·900 watts into 4 ohms,20-20kHz with no more than 0.5% THD·1000 into 2 ohms,20-20kHz with no more than 0.5%· Lit analog power mete | |||
| SL-D | |||||||||||
| SL-K | |||||||||||
| SWX | X-Over | ||||||||||
| SX-2/3 | Proccessor | ||||||||||
| SX-20 | |||||||||||
| TAL | Speaker | 2X30" ribbons, 4X12" woofers, 2 pairs of binding posts, 1 ohmX2 ribbons, 4X4 ohm woofers, 4 ohm total | Piano Black | 86-88 | |||||||
| TAL Upgrade | Speaker | 2X30" ribbons, 4X12" woofers, 2 pairs of binding posts, 6 ohm total | Piano Black | ||||||||
| TAL-Platinum-Black | Speaker | 1X60" ribbon, 4X12" woofers, 2 pairs of binding posts | Piano Black | 89-93 | four 12" woofers in a finite baffle loading. Nominal impedance: 6 ohms. Sensitivity: 88dB/1W/1m. Maximum SPL: 113dB symphonic music, 110dB rock music. Dimensions: 66 inches high, 30 inches wide, 1.5 inches deep. | ||||||
| TAL-Platinum-MK-IV | Speaker | 1X60" ribbon, 4X12" woofers, single pair binding posts, 3 pots | Oak | 93 | |||||||
| TAL-Platinum-Oak | Speaker | 1X60" ribbon, 4X12" woofers, 2 pairs of binding posts | Oak | 89-93 | four 12" woofers in a finite baffle loading. Nominal impedance: 6 ohms. Sensitivity: 88dB/1W/1m. Maximum SPL: 113dB symphonic music, 110dB rock music. Dimensions: 66 inches high, 30 inches wide, 1.5 inches deep | ||||||
| TAL-Silver-Black | Speaker | 1X48" ribbon, 3X12" woofers | Piano Black | 89-93 | |||||||
| TAL-Silver-Oak | Speaker | 1X48" ribbon, 3X12" woofers | Oak | 89-93 | |||||||
| TAL-Silver-SE | 1X48" ribbon, 3X12" woofers | Champagne with gold ribbons | |||||||||
| TD-1200 | Tape Deck | RH-14/RC-TD1400 Remote | Black | 90-92 | |||||||
| TD-1400 | Tape Deck | RH-14/RC-TD1400 Remote | Black | 90-92 | |||||||
| TD-1440 | Tape Deck | RH-40 Remote | Black | 92-93 | |||||||
| TD-1500 | Tape Deck | Black | 90-92 | ||||||||
| TD-1700 | Tape Deck | Black | 90-92 | ||||||||
| TD-1770 | Tape Deck | RH-17 Remote | Black | 90-92 | |||||||
| TDR-1550 | Tape Deck | RH-24 Remote | Black | 92 | |||||||
| TDR-2400 | Tape Deck | RH-24 remote | Black | 90-94 | |||||||
| TFM-15 | Amplifier | T-modded | 2 | 100 | 140 | NO | Black | 90-92 | USA + Taiwan | 100 watts RMS/channel into 8 ohms,20-20kHz with no more than0.1%THD,140 watts RMS/channel into 4 ohms, 20-20kHz with no more than 0.1%THD · 200 watts dynamic power into 2 ohms. Dual analog meters with level selection/B speaker switching · L/R input level controls | |
| TFM-15c | Amplifier | T-modded, Chainable | 2 | 100 | 140 | NO | Black | USA | 100 watts RMS/channel into 8 ohms,20-20kHz with no more than0.1%THD,140 watts RMS/channel into 4 ohms, 20-20kHz with no more than 0.1%THD · 200 watts dynamic power into 2 ohms Dual analog meters with level selection/B speaker switching · L/R input level controls | ||
| TFM-15cb | Amplifier | T-modded, Chainable, Bridgeable | 2 | 100 | 140 | 280 | Black | 92 | USA | 100 watts RMS/channel into 8 ohms,20-20kHz with no more than0.1%THD,140 watts RMS/channel into 4 ohms, 20-20kHz with no more than 0.1%THD · 200 watts dynamic power into 2 ohms Dual analog meters with level selection/B speaker switching · L/R input level controls, Chainable, bridgeable | |
| TFM-22 | Amplifier | T-modded, not Magnetic Field | 2 | 225 | 350 | 600 | Black | 89-91 | USA | 225WPC 8 ohms, 350WPC 4ohms. no meters, Mil-Spec | |
| TFM-24 | Amplifier | LED Power Meters, T-modded, not Magnetic Field | 2 | 225 | 350 | 600 | Black | 91-92 | USA | 225WPC 8ohms, 350WPC 4ohms. no meters, NOT Mil-Spec? Replaced the TFM-22 | |
| TFM-25 | Amplifier | Meters, T-modded, not Magnetic Field | 2 | 225 | 350 | 600 | Black | 89-92 | USA | Sliver Seven Transfer Function Modified·`225 watts RMS/channel into 8 ohms, 20-20kHz with no more than 0.5%THD·350 watts RMS/channel into 4 ohms, 20-20kHz with no more than 0.5% THD·` 600 watts bridged mono` Features analog power meters | |
| TFM-35 | Amplifier | Meters, T-modded | 2 | 250 | 400 | 800 | Black | 92-93 | USA/Japan | Frequency Repsonse: 20-20kHz +0,-0.2dB Power Output: FTC 20hz-20khz 8ohm 250 watts per channel 4ohm 400 watts per channel Bridged mono power output: 800 watts into 8 ohms THD: less than 0.08% Dynamic Headroom: >1.0dB @ 8ohms both channels driven | |
| TFM-35x | Amplifier | THX Certified | 2 | 250 | 400 | 800 | Black | 93 | USA | ||
| TFM-42 | Amplifier | LED Meters, Silver-7t T-modded | 2 | 375 | 500 | 1000 | Black | 89-92 | USA | ||
| TFM-45 | Amplifier | VU Meters, Silver-7t T-modded | 2 | 375 | 500 | 1000 | Black | 89-92 | USA | ||
| TFM-55 | Amplifier | T-modded | 2 | 380 | 500 | 1000 | Black | 92-93 | USA | ||
| TFM-55x | Amplifier | THX Certified | 2 | 380 | 500 | 1000 | Black | 94 | USA | ||
| TFM-6c | Amplifier | Chanable | 2 | 65 | 100 | NO | Black | 91-92 | USA | 65 watts RMS/channel into 8ohms,20-20kHz with no more than 0.1%THD-100 watts RMS/channel into 4 ohms, 20-20kHz with no more than 0.1% THDl · Individual left/right level controls A/B speaker switching · Power and maximum output LED's · Additional line level output for " daisy-chaining" in multi-amp Room-to-Room applications. | |
| TFM-6cb | Amplifier | Chainable, bridgeable | 2 | 65 | 100 | 200 | Black | 92 | USA | Frequency Repsonse: 20-20kHz +0,-0.2dB, Power Output: FTC 20hz-20khz, 8ohm rated 65 watts per channel, 4ohm continuous>100 watts per channel, 8ohm bridged mono >200 watts, THD: less than 0.08% 8ohms both channels driven, Gain: 29.0 dB, Input Impedance 30 kohms | |
| TFM-75 | Amplifier | dynamic 1300w@2ohm, dual power cords, T-modded | 2 | 750 | 1000 | NO | Black | 92 | USA | ||
| TL-3100 | CD Player | RH-31/RC-3100 Remote | Anthracite | 89-91 | |||||||
| TL-3200 | CD Player | 22120227 Remote | Anthracite | 89-91 | |||||||
| TL-3220 | CD Player | 22120227 Remote | Anthracite | 90-91 | |||||||
| TL-3300 | CD Player | HTR002-0060 Remote | Anthracite | 89-91 | |||||||
| TLM-3600 | CD Player | RH-36 Remote, handles, made by Yamaha, uses Yamaha 10CD cartridges | Black | 90-91 | |||||||
| TS-D60-Sub/Sat | Speaker | 92-93 | |||||||||
| TS-P80-Sub/Sat | Speaker | 92-93 | |||||||||
| TS-S20-Satellites | Speaker | 92-93 | |||||||||
| TS-S30-Sub/Sat-Black | Speaker | 92-93 | |||||||||
| TS-S30-Sub/Sat-Oak | Speaker | 92-93 | |||||||||
| TX-10 | Tuner | Black | 89-92 | ||||||||
| TX-11 | Tuner | FM | Anthracite | 82-85 | |||||||
| TX1-11 | Processor | 82-85 | FM Stereo Multiplex Decoder | ||||||||
| TX-11a | Tuner | AM/FM | Anthracite | 86-90 | |||||||
| TX-11b | Tuner | AM/FM/Stereo AM | Black | 89 | |||||||
| TX-12 | Tuner | RH-12/RC-TX12 Remote | 89-92 | ||||||||
| TX-14 | Tuner | 92-93 | |||||||||
| TX-2 | Tuner | Anthracite | 85-90 | Japan | |||||||
| TX-Seven | Car Deck | ||||||||||
| TX-8r | Tuner | TX-8 EYE Remote | Black | 93 | Japan | 20 easy-to-program Station Selector buttons that are configureable in any combination of FM and/or AM stations as desired Illuminated Signal-Strength Meter that compliments the Power Meters seen on Carver Amplifiers RCA-type Output Jacks FM & AM Antenna Connectors Works remotely via a Carver RH-75 remote | |||||
| TX-Nine | Car Deck | ||||||||||
| TX-Iib | Pro Tuner | ||||||||||
| XA-22 | Proccessor | 92-94 | Frequency Response ( processing off ) : 25Hz-20kHz ( + 0,- 1dB ) , Processing Response: Sub- bass restoration 25Hz-65Hz ( + 3dB ), Sub-sonic Filter: - 3dB @ 12 Hz, Signal-to-Noise ( A - wtd ) :> 95 dB ( ref. to 1.0V rms output ), Distortion: <0.1 % ( processing off ), Input Impedance: 100 kohms, Max Input Level : 6V rms, Output Impedance: 470 ohms, Max Output Level: 6V rms Operating Voltage : 10-16 VDC, Dimensions : 1.5"H x 6"W x 3.25"D, Net Weight: 0.9lbs | ||||||||
| XA-23 | Proccessor | 92-94 | Frequency Response ( processing off ) : 25Hz-20kHz (+ 0,- 1dB), Precess EQ: 200Hz+ 20dB, 500Hz + 17dB, 1.3kHz + 12dB, Signal-tp Noise ( A -Wtd): > 90dB (ref. To 1.0V rms output), Distortion: < 0.1% Input Impedance: 100 kohms, Max Input Level: 6V rms, Output Impedance: 470 ohms, Max Output Level: 6V rms minimum, Operating Voltage: 10- 16VDC, Dimensions: 1.5"H x 6"W x 3.25"D, Net Weight: 0.8lbs | ||||||||
| XA-24 | Proccessor | 92-94 | Frequency Response ( processing off ) : 25HZ-20Hz (+0,-1dB), Process EQ ( nominal): 600Hz and below + 8dB, 1.2kHz + 10dB, 3.4kHz and above +5dB, Delay: Variable 7-20ms below 1kHz, Signal-to-Noise ( A-Wtd): > 85dB (ref. To 1.0V rms output), Distortion: <0.1% Input Impedance: 100 kohms, Max Input Level: 6V rms, Output Impedance: 470 ohms, Max Output Level: 6V rms, Operating Voltage: 10-16VDC, Dimensions: 1.5"H x 6"W x 3.25"D, Net Weight: 1.3lbs | ||||||||
| XA-25 | X-Over | 92-94 | Frequency Response ( with Subsonic Filter ) : 20Hz-20kHz (+ 1 dB ) , Subsonic Filter : -3dB @ 13Hz, Crossover Filter : Programmable 18dB/octave slope, Signal-to-Noise ( A-Wtd): 90dB (ref. To 1V rms output), Distortion: <0.1%, Input Impedance: 100 kohms, Max Input Level: 6V rms, Output Impedance: 470 ohms, Max Output Level: 6V rms, Operating Votage: 10- 16VDC, Dimensions: 1.5"H x 6"W x 3.25"D , Net Weight: 0.8lbs | ||||||||
| XA-27 | X-Over | 92-94 | Subsonic Filter : - 3dB @ 11Hz, Crossover Frequency: Variable ( 50Hz - 160Hz ) 24dB/octave slope, Signal-to-Noise ( A -Wtd): > 95dB (ref. to 1.0V rms output), Distortion: <0.1 %, Input Impedance: 100 kohms, Max Input Level: 6V rms, Output Impedance: 330 ohms, Max Output Level: 6V rms, Operating Voltage: 1--16VDC, Dimensions: 1.5" H x 6"W x 3.25"D, Net Weight : 0.8lbs | ||||||||
| XA-28 | X-Over | 92-94 | Frequency Response: Flat within bandpass range, Sinal-to-Noise ( A-Wtd)> 90dB (ref. To 1.0V rms output), Distortion:< 0.1% Input Imoedance: 100khms, Max Input Level: 6V rms, Output Impedance: 470 ohms, Max Output Level:6V Operating Voltage: 10-16VDC, Dimensions: 1.5"H x 6"W x 3.25"D, Net Weight: 0.9lbs | ||||||||
| XA-50 | Car Amp | 92-94 | Power Output: 25 watts rms/channel @ 4 ohms ( contunuous with both driven ), 60 watts rms/channel @ 2 ohms ( Contunuous with both driven ), Mono: 120 watts rms cont. @ 4 ohms, Frequency Response ( for 1 watts into 4 ohms load) : 20Hz-20kHz (+0,-1dB), Minimum Load Impedance : 2 ohms recommended (4 ohms recommended for bridged operation), Signal to Noise Ratio ( IHF A-Wtd_;>90 dB, Maximum Gain ( with input level controls fully clockwise): 31dB, Input Sensitivity ( for full power into 4 ohms with input level control fully clockwise); 282mV rms, Input Impedance: 20 kohms, Operating Voltage: 9.5 to 16 volts DC, Supply Switching; 100kHz ( TMOS MOSFET design), Harmonic Distortion ( YHD + Noise at 1 watts ): < , 02% | ||||||||
| XEQ-15 | Equalizer | 92-94 | Frequency Response: 20HZ-20KHZ ( x 1db ), Center Frequencies: 22Hz, 31.3Hz, 50Hz, 80Hz, 125Hz, 200Hz, 400Hz, 800Hz, 1.6kHz, 2.5kHz, 4kHz, 6.3kHz, 9kHz, 12.5kHz, 18kkHz ( +/-10%), Equalizar Range: +10db (+2db), Signal to Noise:>105 db Ref. To Maximum Output >91 db Ref. To 1V rms output, Distortion: <0.1% ( 0.05% typical), Input Impedance : 100 kohms, Maximum Input Level : 10V rms, Output Impedance: 470 ohms, Maximum Output Level: 10V rms, Channel Separation: > 70dB@1kHz, Operating Voltage : 10-16VDC, Dimensions ( H x W x D ) : 1.75H" x 7.6W" x 8.5D", Net Weight : 3.0 lbs | ||||||||
| Z-1 | Single channel power expander | ||||||||||
| Z-2 | |||||||||||
| Z-5 | 5 channel power expander | ||||||||||
| ZAP | Remote System Link | 92 | |||||||||
| ZZ | |||||||||||